11/9/2022 0 Comments Nrg quick release kit spinning
The final touch to compliment the exterior was AIT Racing’s carbon fiber spoiler. The Scion RS 7.0 “DAMD” kit, flowed perfectly. With the sideskirts and rear lip George wanted to keep it simple. With the gunmetal color in mind an AIT Racing OEM style carbon fiber hood was added, along with a Bomex carbon fiber front lip. George went more simple than over the top with the redo. In different angles, the car has a blue-ish sparkle to it and enhances the body. That color selection turned out to be amazing. There he decided on a gunmetal color from an Audi R8. With a lot of thinking and decisions to make, George passed his car down to A&A Auto Works in Van Nuys. A little color, but also keep that aggressive look. He wanted to give some new color to his then black xB. To correct those areas that he should have touched to begin with. Everyone else that I let drive the car though uses the steering wheel to some degree as it is really the only "handle" that can be used.George wanted to do a complete overhaul of his car. That leaves a dirty spot on the paint though. I personally hold onto the A pillar with my left hand and drop into the car and then pull myself out with the same technique. The reason I say that is because other than the steering wheel there isn't a whole lot to hold onto if you are wiggling in and out of these. Obviously you can, but I wouldn't recommend it. #Nrg quick release kit spinning installSo, do older guys install these for ease of accessibility? and still have to lever in and out of these cars. The GT I am considering right now has actually been lowered a bit. I am in my late fifties and thinking strongly about an '88 GT or Formula. Didn't see any comments about improving the ease of getting into or out of the car. I understand the theft deterrent reason for installing a quick release steering wheel. Reviving this old topic to ask a question. #Nrg quick release kit spinning updateHope this helps, I will update as needed: Place the steering wheel up and line up the holes, place in the screws and whaalllaaa!! dont forget, depending on the horn button, there is a round metal piece that comes with the NRG Quick release kit that may be required to keep horn in place on the steering wheel. Once the bottom hub is on, you can now hook up the horn from the steering wheel. Now you want to place the bolt back on the steering column and tighten down real tight and then place the "D" pin back on over the bolt area.Īlso, do not forget to solder and cover the positive horn wire with heat shrink. Be sure to tuck all the wires in and now bolt the quick release bottom section onto the short hub. Now you want to place the spring in the hub hole where the aluminum piece was that you took out for horn supression, this will keep the wire in contact with the positive (+) connection. Here you want to take the NRG Short Hub (short hub #170) and place it on the steering column with the NRG on the top sideĪt this time you can go ahead and hook up the negative wire for the horn to the quick realse hub that connects to the main hub that you just put on steering wheel. Take a wire and fix it to the BOTTOM of the spring and slide the black pin back over top (hold on to this for late use). You will want to take the aluminum pin out by twisting the black pin (carefull it does have a spring behind it). When the steering wheel is off, it should look like this: Use a wrench or socket to press and pull off the steering wheel. Place the center of the remover kit with the threaded bolts already in the sides of the center bracket then use the threaded bolts on the remover kit and place in holes (there are two just alike on the steering wheel center). #Nrg quick release kit spinning driverUse a flat head screw driver to take off the pin just above the 13/16th bolt, and then take off the bolt. Take off the horn pad using a flat head screw driver and pry from the side (there is a small opening if you look for and it should just pop off). (These can be purchased at any local auto store) You need to take off the current steering wheel on you Fiero with the steering wheel remover kit. NRG second generation Quick Release #srk-200 (cbk) - (the cbk stands for carbon/black) Since I was having yet another hard time finding the correct way to install after market steering wheels and short hubs with quick releases on Fieros and still keep your horn I thought I would do another write up.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |